Company News Published:2026-11-19

Serpentine Heat Exchanger Tubes: One-Piece Formed, No Butt Welds, Stainless Steel Coil Bundles Manufacturer

Manufacturer of one-piece formed serpentine heat exchanger tubes with no butt welds. CNC continuous bending to drawing; materials include 304, 316L, 321, 2205 and 2507 duplex stainless welded tubes, with hydrostatic testing, eddy-current inspection, online solution annealing and pickling passivation. Suited for waste heat recovery, flue-gas heat exchange, chemical cooling, NEV liquid cooling and desulfurization equipment, with full quality documentation supplied.

For purchasers and engineers working on environmental protection, chemical and waste-heat recovery projects, this article is for you if you are looking for butt-weld-free, one-piece formed serpentine heat exchanger tubes and coil bundles.

01. With serpentine tubes, the problem is rarely just one weld

The last thing you want is a leak discovered after the tube bundle is installed and the equipment is running. The weld is only one of the weak points; the issues that most trouble purchasers and engineers usually include:

✔ Welded joint itself: the butt weld between straight sections is a natural weak point; under condensate corrosion and pressure cycling, it fails first.

✔ Bend thinning: wall thinning and out-of-roundness on the outer bend reduce both pressure capacity and heat-transfer area.

✔ Cracking and wrinkling: when bending parameters are not set correctly, the bend wrinkles, cracks or shows an orange-peel inner surface, with stress concentrated at these spots.

✔ HAZ sensitization: if the two sides of the weld are not solution-treated, intergranular corrosion starts from the heat-affected zone.

✔ Internal weld bead and misalignment: mismatched fit-up, incomplete root penetration and internal weld bead lead to perforation once the medium flows through.

✔ Single-tube pressure test only: if the assembled bundle is not subjected to an overall hydrostatic test, problems are left for the customer's site.

✔ Material and passivation: mixed material, untraceable mill certificates and inadequate pickling passivation leave residual iron ions that trigger pitting corrosion.

Our serpentine heat exchanger tubes are continuously CNC-bent from a single raw tube, formed in one piece with no butt welding throughout, eliminating the leak risk of butt welds at the source. Bending parameters, overall pressure testing, material traceability and pickling passivation are all closed-loop controlled in our own workshop.

02. One continuous tube bent into a complete serpentine bundle

CNC continuous bending produces smooth, full-radius arcs with an even tube wall—no scoring, wrinkling or cracking—fully preserving the original mechanical properties and corrosion resistance of the base material.

Each complete serpentine bundle is formed by continuous bending from long tubing, with every technical clause of the customer's drawing strictly followed throughout production; quality control standards are not compromised.

03. Every requirement on the drawing, we deliver

Taking the drawing requirements of this serpentine heat exchanger tube as an example:

✔ Tube: stainless welded heat-exchanger tube, per GB/T 21832.2-2018

✔ Forming: continuous bending from one tube, one-piece formed, no butt welds

✔ Bending: fixed R60 bend radius, no cracking or wrinkling after bending

✔ Pressure test: overall hydrostatic test after bundle forming, held under pressure, with a test report issued

✔ Traceability: each batch comes with a material certificate (MTC), verified batch by batch, 100% inspection

✔ Corrosion protection: pickling passivation after completion, passivation quality tested per GB/T 25150

04. Customization scope

✔ Main products: one-piece formed serpentine heat exchanger tubes, serpentine coil tubes, complete serpentine tube bundles

✔ Available materials: 304, 316L, 321, 2205, 2507 duplex stainless welded heat-exchanger tubes

✔ Supporting processes: CNC continuous tube bending, hydrostatic testing, eddy-current inspection, online solution annealing, pickling passivation

✔ Application conditions: industrial waste heat recovery, flue-gas heat exchange and reheating, chemical medium cooling, NEV liquid cooling, desulfurization environmental equipment

✔ Delivery assurance: produced strictly to drawing; material certificate, pressure test report and inspection report provided on request

For the same serpentine tube drawing, the process route makes a huge difference. Products with butt welds carry a long-term hidden hazard; our continuous-bending, one-piece formed process removes one weld seam and one leak risk, making the tubes better suited to demanding corrosion and pressure conditions.

If you want to avoid weld-seam leakage and procure one-piece formed serpentine heat exchanger tubes, please share your drawing, medium, pressure and temperature parameters; we will align on a technical solution and support sample testing. Purchasers and engineers are welcome to inquire.

Back to News List Contact Us